Steps In Pool Table Refelting Denver
Pool tables are elegant designs for indoor sports rooms or patios. Most people play pool to as a way of spending leisure time with family or friends. When the tables are made from durable materials, they are able to last for over 20 years with very minimal maintenance. The felt is the most vulnerable part of the structure. When considering pool table refelting Denver residents have various things to consider.
The felt is the fabric which is attached to the surface of the table. When re-felting, the first step is to determine the size of the pool table using a measure tape. The felt is then replaced at a sports shop or home improvement depot. The material should be purchased such that there is an extra 12 inches to the width and length. Because there are many colors, it will be important to decide if the same color as the one being replaced will be used or a different one.
After the choice of color, the rails need to be removed using a crescent wrench. This is done by removing the bolts that attach the rails. Rails are also always covered by the felt and need to be re-felted too. This explains the need to buy extra material. Rails are carefully placed on the floor close to the table so that there is no mistake when reattaching them.
The felt that needs to be replaced gets removed using a staple remover. It is used for pulling out the staples at the felt edge. Caution should be taken to ensure there is removal of all felt from the surface of the table. The old felt should be placed on a thrash bag and disposed of later.
The new felt needs to be carefully placed while taking care to inspect that no damaged are done and that there are no stains. A sharp scissor should then be used to cut it, using the border of the table to guide you. Some felt is left over to be used to re-felt the rails.
After the cut has been made, the felt is attached to the top of the table using a stapler. The stapling should start at the mid portion of one end of the felt before the right and left edges are stapled. After this, you should go to the opposite end and tightly pull the felt. It is then stapled in the same way as the previous side.
The edges then get stapled. It is important to ensure that the staples are placed at an equal distance from each other and that they are lined correctly. When it comes to the pockets, there should be cutting of 3 slits on each of them before wrapping and stapling of the felt on the pocket edges. It is then pulled tightly before being stapled.
Finally, the structure is reassembled. Rails will be attached to their original positions using a crescent wrench. The pocket lines are inserted and the table is ready for use.
The felt is the fabric which is attached to the surface of the table. When re-felting, the first step is to determine the size of the pool table using a measure tape. The felt is then replaced at a sports shop or home improvement depot. The material should be purchased such that there is an extra 12 inches to the width and length. Because there are many colors, it will be important to decide if the same color as the one being replaced will be used or a different one.
After the choice of color, the rails need to be removed using a crescent wrench. This is done by removing the bolts that attach the rails. Rails are also always covered by the felt and need to be re-felted too. This explains the need to buy extra material. Rails are carefully placed on the floor close to the table so that there is no mistake when reattaching them.
The felt that needs to be replaced gets removed using a staple remover. It is used for pulling out the staples at the felt edge. Caution should be taken to ensure there is removal of all felt from the surface of the table. The old felt should be placed on a thrash bag and disposed of later.
The new felt needs to be carefully placed while taking care to inspect that no damaged are done and that there are no stains. A sharp scissor should then be used to cut it, using the border of the table to guide you. Some felt is left over to be used to re-felt the rails.
After the cut has been made, the felt is attached to the top of the table using a stapler. The stapling should start at the mid portion of one end of the felt before the right and left edges are stapled. After this, you should go to the opposite end and tightly pull the felt. It is then stapled in the same way as the previous side.
The edges then get stapled. It is important to ensure that the staples are placed at an equal distance from each other and that they are lined correctly. When it comes to the pockets, there should be cutting of 3 slits on each of them before wrapping and stapling of the felt on the pocket edges. It is then pulled tightly before being stapled.
Finally, the structure is reassembled. Rails will be attached to their original positions using a crescent wrench. The pocket lines are inserted and the table is ready for use.
You are receiving this because you signed up for it on 2011-08-21 from IP 72.177.83.171
To fine-tune your selection of which articles to receive, just login here
using your username:
To unsubscribe please use the following link:
Unsubscribe
